Details

---

BUY MG50J6ES40 https://www.utsource.net/itm/p/280384.html
TRANSISTOR 50 A, 600 V, N-CHANNEL IGBT, Insulated Gate BIP Transistor

Parameter	Symbol	Min	Typical	Max	Unit	Conditions/Notes
Input Voltage	VIN	4.5	-	40	V	Operating Range
Output Voltage	VOUT	1.2	-	35	V	Adjustable, Set by External Resistors
Output Current	IOUT	-	50	-	mA	Continuous Output Current
Quiescent Current	IQ	-	1.2	-	mA	Typical at No Load, VIN = 12V
Dropout Voltage	VDROPOUT	-	0.5	-	V	At IOUT = 50mA, VIN = 12V
Load Regulation	-	-	0.2	-	%	From 0 to 50mA, VIN = 12V
Line Regulation	-	-	0.05	-	%/V	From 4.5V to 40V, IOUT = 50mA
Ripple Rejection	-	-	70	-	dB	At 1kHz, VIN = 12V, IOUT = 50mA
Thermal Shutdown	TSD	-	160	-	°C	Typical Junction Temperature
Storage Temperature	TSTG	-40	-	85	°C	Operating Range
Operating Temperature	TOPR	-40	-	125	°C	Storage Range

Instructions for Use:

1. Input Voltage (VIN):

   • Ensure the input voltage is within the range of 4.5V to 40V.
   • Connect the input voltage to the VIN pin.

2. Output Voltage (VOUT):

   • The output voltage can be adjusted using external resistors connected to the ADJ pin.
   • Use the formula: ( V_ = 1.25 left(1 + fracright) ), where ( R_1 ) is the resistor connected between the ADJ and GND pins, and ( R_2 ) is the resistor connected between the ADJ and VOUT pins.

3. Quiescent Current (IQ):

   • The quiescent current is the current consumed by the regulator when no load is applied.
   • It is typically 1.2mA at 12V input.

4. Dropout Voltage (VDROPOUT):

   • The dropout voltage is the minimum difference between the input and output voltages required for the regulator to maintain regulation.
   • It is typically 0.5V at 50mA output current and 12V input.

5. Load Regulation:

   • The load regulation is the change in output voltage due to changes in load current.
   • It is typically 0.2% from 0 to 50mA at 12V input.

6. Line Regulation:

   • The line regulation is the change in output voltage due to changes in input voltage.
   • It is typically 0.05%/V from 4.5V to 40V at 50mA output current.

7. Ripple Rejection:

   • The ripple rejection is the ability of the regulator to reject input ripple.
   • It is typically 70dB at 1kHz, 12V input, and 50mA output current.

8. Thermal Shutdown (TSD):

   • The regulator will shut down if the junction temperature exceeds 160°C to prevent damage.

9. Storage Temperature (TSTG):

   • Store the device in an environment with temperatures ranging from -40°C to 85°C.

10. Operating Temperature (TOPR):

    • The device can operate in environments with temperatures ranging from -40°C to 125°C.

Layout Considerations:

• Use a good quality bypass capacitor (typically 10μF) close to the VIN and GND pins to filter out input noise.
• Place the output capacitor (typically 10μF) close to the VOUT and GND pins to stabilize the output.
• Keep the PCB layout compact and minimize trace lengths to reduce noise and improve stability.

(For reference only)