Details

---

BUY AD7714AR-5 https://www.utsource.net/itm/p/1117295.html
Metal Oxide Varistor MOV; Voltage Rating AC, Vrms:680Vrms; Voltage Rating DC, Vdc:895VDC; Peak Surge Current 8/20uS, Itm:4500A; Clamping Voltage 8/20us Max :1815V; Capacitance, Cd:140pF; Package/Case:14mm Disc

Below is the parameter table and instructions for the AD7714AR-5, a 24-bit, sigma-delta analog-to-digital converter (ADC) from Analog Devices.

AD7714AR-5 Parameter Table

Parameter	Symbol	Min	Typ	Max	Unit
Supply Voltage	VDD	2.7	5.25	5.25	V
Supply Current (Active)	IDD	-	1.8	-	mA
Supply Current (Standby)	IDD	-	0.5	-	μA
Input Range	VIN	0	-	VREF	V
Reference Voltage	VREF	2.5	5.0	-	V
Resolution		-	24	-	bits
Conversion Time (Single)	tCONV	-	133	-	ms
Output Data Rate	fODR	0.1	100	19200	Hz
Differential Nonlinearity	DNL	-1	0	+1	LSB
Integral Nonlinearity	INL	-2	0	+2	LSB
Signal-to-Noise Ratio	SNR	-	110	-	dB
Total Harmonic Distortion	THD	-	-100	-	dB
Operating Temperature	Toper	-40	85	125	°C
Storage Temperature	Tstg	-65	150	-	°C

Instructions for Using AD7714AR-5

1. Power Supply:

   • Connect the VDD pin to a stable power supply between 2.7V and 5.25V.
   • Connect the GND pin to the system ground.

2. Reference Voltage:

   • Apply a reference voltage (VREF) between 2.5V and 5.0V to the VREF pin. This reference voltage determines the input range of the ADC.

3. Analog Input:

   • Connect the analog signal to be converted to the appropriate input pins (AIN1, AIN2, etc.). The input signal should be within the range of 0 to VREF.

4. Digital Interface:

   • The AD7714AR-5 supports SPI (Serial Peripheral Interface) communication. Connect the following pins:
     • SCLK: Serial Clock
     • DIN: Data In
     • DOUT: Data Out
     • CS: Chip Select

5. Configuration:

   • Use the configuration registers to set up the ADC according to your requirements. Key registers include:
     • Mode Register: Sets the operating mode (e.g., single conversion, continuous conversion).
     • Setup Register: Configures the input channel, gain, and filter settings.
     • Data Register: Reads the converted data.

6. Conversion:

   • To start a conversion, write the appropriate command to the Mode Register.
   • For single conversions, wait for the conversion to complete before reading the data.
   • For continuous conversions, data can be read at the specified output data rate.

7. Reading Data:

   • After a conversion is complete, read the data from the Data Register using the SPI interface.
   • The data is 24 bits long and is transmitted MSB first.

8. Power Management:

   • To reduce power consumption, use the Standby mode by writing to the appropriate register.
   • To return to active mode, write the appropriate command to the Mode Register.

9. Temperature Considerations:

   • Ensure that the operating temperature is within the specified range (-40°C to 125°C).
   • Store the device within the storage temperature range (-65°C to 150°C).

10. Handling:

    • Handle the device with care to avoid static discharge and physical damage.
    • Follow proper ESD (Electrostatic Discharge) precautions when handling the device.

By following these instructions, you can effectively use the AD7714AR-5 in your analog-to-digital conversion applications.

(For reference only)