Details

---

BUY TMS320C31PQL60 https://www.utsource.net/itm/p/1736655.html
DIGITAL SIGNAL PROCESSORS

Parameter	Description	Value
Device Type	Digital Signal Processor (DSP)	TMS320C31PQL60
Architecture	C3x DSP Core	32-bit
Clock Speed	Maximum Clock Frequency	40 MHz
Power Supply Voltage	VCC (Core)	5.0V ± 5%
I/O Voltage	VIO	5.0V ± 5%
Operating Temperature	Industrial Range	-40°C to +85°C
Package Type	Plastic Quad Flatpack (PQFP)	144-pin
Program Memory	On-chip Program Memory	60 KB (30K x 16-bit)
Data Memory	On-chip Data Memory	4 KB (2K x 16-bit)
I/O Ports	Number of I/O Pins	64
Timer/Counters	Number of Timers/Counters	2
Serial Ports	Number of Serial Ports	2 (McBSP)
Interrupts	Number of Interrupts	37
DMA Channels	Number of DMA Channels	8
Bus Width	Data Bus Width	16-bit
Address Bus Width	Address Bus Width	24-bit
Instruction Set	Instruction Set Architecture	C3x
Power Consumption	Typical Power Consumption at 40 MHz	1.5W
Programming Model	Number of Registers	32 General Purpose Registers
Multiplier	Hardware Multiplier	32-bit x 32-bit
Multiplier Latency	Multiplier Latency	1 cycle
Multiplier Throughput	Multiplier Throughput	1 cycle
Pipeline Stages	Number of Pipeline Stages	6
Package Dimensions	Package Size	24 mm x 24 mm
Pin Pitch	Pin Pitch	0.5 mm

Instructions for Use:

1. Power Supply:

   • Connect the VCC pin to a 5.0V ± 5% power supply.
   • Connect the VIO pin to a 5.0V ± 5% power supply for I/O operations.

2. Clock Configuration:

   • Connect an external crystal or oscillator to the XIN and XOUT pins to provide the clock signal.
   • Ensure the clock frequency does not exceed 40 MHz.

3. Reset:

   • Apply a low signal to the RESET pin to reset the processor.
   • Hold the reset signal for at least 2 clock cycles before releasing it.

4. Programming:

   • Use a JTAG interface or parallel programming method to load the program into the on-chip memory.
   • Ensure the program is correctly formatted for the C3x instruction set.

5. Memory Access:

   • Use the address bus to access the 60 KB of program memory and 4 KB of data memory.
   • Ensure that memory accesses do not exceed the addressable range.

6. Interrupt Handling:

   • Configure the interrupt vectors in the program memory to handle interrupts.
   • Use the interrupt controller to manage and prioritize interrupts.

7. DMA Operations:

   • Configure the DMA channels to transfer data between memory and peripherals without CPU intervention.
   • Ensure that DMA transfers do not conflict with CPU memory accesses.

8. Serial Communication:

   • Use the McBSP (Multichannel Buffered Serial Port) for serial communication.
   • Configure the McBSP settings according to the communication protocol requirements.

9. Timer/Counter Usage:

   • Use the timers/counters for timing and counting applications.
   • Configure the timer/counter registers to set the desired time intervals or count values.

10. Thermal Management:

    • Ensure adequate heat dissipation by using a heatsink if necessary.
    • Monitor the operating temperature to ensure it remains within the specified range.

11. Storage and Handling:

    • Store the device in a dry, static-free environment.
    • Handle the device with care to avoid damage to the pins and package.

For detailed information and specific application notes, refer to the TMS320C31PQL60 datasheet and user manual provided by Texas Instruments.

(For reference only)