Details

---

BUY DSPIC30F2010-20I/SPG https://www.utsource.net/itm/p/9495296.html

Parameter	Description	Value
Part Number	Device Identifier	DSPIC30F2010-20I/SPG
Package	Physical Package Type	28-Pin SSOP (Small Outline Package)
Operating Voltage (Vdd)	Supply Voltage Range	2.0V to 5.5V
Operating Temperature (Tamb)	Ambient Operating Temperature Range	-40掳C to +85掳C
Flash Memory	Program Memory Size	8 KB (4K x 16-bit words)
RAM	Data Memory Size	512 bytes (256 x 16-bit words)
EEPROM	Non-Volatile Data Memory	256 bytes (128 x 16-bit words)
Clock Frequency	Maximum Clock Frequency	30 MHz (5 MIPS)
Analog-to-Digital Converter (ADC)	ADC Channels and Resolution	10-bit, 10 channels
Digital-to-Analog Converter (DAC)	DAC Channels and Resolution	Not Available
Timers	Number and Type of Timers	3 x 16-bit Timers
Capture/Compare/PWM Modules	Number and Type of CCP Modules	3 x 16-bit CCP Modules
Serial Communication Interfaces (SCI/SPI/I2C)	Number and Type of Serial Interfaces	1 x SCI, 1 x SPI, 1 x I2C
Interrupts	Number of Interrupt Sources	29
Power Management	Low Power Modes	Idle, Sleep
Watchdog Timer (WDT)	Watchdog Timer	Yes
Brown-out Reset (BOR)	Brown-out Reset	Yes
Internal Oscillator	Internal Oscillator Frequency	4 MHz (卤1%)
External Oscillator	External Oscillator Support	Crystal, Ceramic Resonator, External Clock
Pin Count	Total Number of Pins	28
I/O Ports	Number of I/O Pins	22
Programming Interface	In-Circuit Serial Programming (ICSP)	Yes
Package Marking	Package Marking	DS30F2010I
RoHS Compliance	RoHS Compliant	Yes

Instructions for Use

1. Power Supply:

   • Ensure that the Vdd supply voltage is within the range of 2.0V to 5.5V.
   • Connect the Vss pin to ground.

2. Clock Configuration:

   • Configure the internal or external oscillator as per your application requirements.
   • For external oscillators, connect the appropriate crystal or resonator to the OSC1 and OSC2 pins.

3. Programming:

   • Use the ICSP interface for programming the device.
   • Connect the PGD (Data), PGC (Clock), and PGM (Programming Voltage) pins to the programmer.

4. I/O Configuration:

   • Configure the I/O pins as inputs or outputs using the TRIS registers.
   • Use the PORT registers to read or write data to the I/O pins.

5. ADC Configuration:

   • Enable the ADC module and configure the channel selection and conversion trigger.
   • Read the converted values from the ADC result registers.

6. Timer and CCP Module Configuration:

   • Set up the timers and CCP modules for timing, capture, compare, or PWM functions.
   • Use the appropriate registers to configure the prescaler, mode, and interrupt settings.

7. Serial Communication:

   • Initialize the SCI, SPI, or I2C modules for serial communication.
   • Use the respective control and status registers to manage data transmission and reception.

8. Interrupt Handling:

   • Enable the required interrupts and set up the interrupt service routines (ISRs).
   • Use the INTCON register to manage global and peripheral interrupts.

9. Low Power Modes:

   • Enter the idle or sleep mode to reduce power consumption.
   • Use the SLEEP instruction to enter sleep mode and the WDT or external interrupts to wake up the device.

10. Watchdog Timer:

    • Enable the WDT to prevent system lockup.
    • Clear the WDT periodically to prevent a reset.

11. Brown-out Reset:

    • Enable the BOR to reset the device if the supply voltage drops below a threshold.
    • Configure the BOR level using the configuration bits.

12. Storage and Handling:

    • Store the device in a dry, static-free environment.
    • Handle the device with care to avoid damage to the pins and internal components.

For detailed information, refer to the datasheet and user manual provided by Microchip Technology.

(For reference only)