Details

---

BUY PIC10F322T-I/OT https://www.utsource.net/itm/p/11249022.html

Parameter	Description	Value
Package	Package Type	SOT-23-6
Operating Voltage (Vdd)	Supply Voltage Range	2.0V to 5.5V
Operating Temperature	Operating Temperature Range	-40°C to +85°C
Program Memory	Flash Program Memory Size	512 x 14-bit words
Data Memory	RAM Data Memory Size	25 x 8-bit registers
EEPROM	EEPROM Data Memory Size	64 x 8-bit registers
Oscillator	Oscillator Types	Internal (LFINTOSC, HFINTOSC), External Crystal/Ceramic Resonator, External Clock
Clock Frequency	Maximum Clock Frequency	32 MHz (with external clock)
Analog-to-Digital Converter (ADC)	ADC Channels	6 channels (AN0-AN5)
ADC Resolution	ADC Resolution	10-bit
Comparators	Number of Comparators	2
Timer/Counters	Timer1	16-bit timer/counter with prescaler
Timer/Counters	Timer2	8-bit timer/counter with prescaler and postscaler
Peripheral Pin Select (PPS)	PPS Support	Yes
Power Management	Sleep Current	< 50 nA (typical)
Wake-up Sources	Wake-up Sources	Pin change, Timer1, Comparator, Brown-out Reset, Watchdog Timer
Watchdog Timer (WDT)	WDT Prescaler	1:1 to 1:32768
Brown-out Reset (BOR)	BOR Threshold	1.9V, 2.5V, 4.2V (selectable)
Reset	Reset Sources	Power-on Reset (POR), Brown-out Reset (BOR), Watchdog Timer (WDT), External MCLR pin
Programming	Programming Method	In-Circuit Serial Programming (ICSP)
Programming Voltage	Programming Voltage	4.5V to 5.5V (MCLR pin)
Pin Configuration	Pin Count	6
I/O Pins	Number of I/O Pins	5 (RA0-RA4)
Communication Interfaces	Communication Interfaces	MSSP (SPI, I2C)
Interrupts	Interrupt Sources	Timer1, Timer2, ADC, Comparator, External Interrupt, Brown-out Reset, Watchdog Timer

Instructions for Using the PIC10F322T-I/OT

1. Power Supply:

   • Connect the Vdd pin to the positive supply voltage (2.0V to 5.5V).
   • Connect the Vss pin to ground.

2. Oscillator Configuration:

   • For internal oscillator, configure the OSCCON register.
   • For external crystal/ceramic resonator or clock, connect the appropriate components to the OSC1 and OSC2 pins.

3. Program Memory:

   • Use a programmer that supports ICSP to program the device.
   • Ensure the MCLR pin is held at the programming voltage (4.5V to 5.5V) during programming.

4. Data Memory:

   • Access the RAM data memory using the direct addressing mode in your code.
   • Use the EEPROM memory for non-volatile data storage by writing to and reading from the appropriate registers.

5. Analog-to-Digital Converter (ADC):

   • Configure the ADCON0 and ADCON1 registers to select the channel and resolution.
   • Start the conversion by setting the GO/DONE bit in the ADCON0 register.

6. Comparators:

   • Configure the CMCON register to set up the comparators.
   • Use the output of the comparators for various applications such as level detection.

7. Timer/Counters:

   • Configure the TMR1 and TMR2 registers to set up the timers.
   • Use the prescaler and postscaler settings to adjust the timing intervals.

8. Peripheral Pin Select (PPS):

   • Use the PPS configuration registers to assign functions to specific pins.

9. Power Management:

   • Enter sleep mode by clearing the SLEEP bit in the WDTCON register.
   • Configure the WDT and BOR settings to manage power consumption and reset conditions.

10. Interrupts:

    • Enable interrupts by setting the GIE and PEIE bits in the INTCON register.
    • Configure individual interrupt sources by setting the corresponding enable bits in the respective control registers.

11. Communication Interfaces:

    • Configure the MSSP module for SPI or I2C communication by setting up the SSPCON1 and SSPCON2 registers.

12. Reset:

    • Ensure the MCLR pin is connected to a pull-up resistor to Vdd for normal operation.
    • Use the reset sources to manage system initialization and recovery.

For detailed information and specific register configurations, refer to the PIC10F322T-I/OT datasheet and application notes provided by Microchip Technology.

(For reference only)