Details

---

BUY NJM2595M https://www.utsource.net/itm/p/11624583.html
IC VIDEO SWITCH 5-IN/3-OUT 16DMP

Parameter	Symbol	Conditions	Min	Typ	Max	Unit
Supply Voltage	VCC	-	4.5	5.0	5.5	V
Quiescent Current	IQ	VCC = 5V	-	1.5	-	mA
Output Current (Per Channel)	IOUT	VCC = 5V, RL = 8Ω	200	300	400	mA
Output Power (Per Channel)	POUT	VCC = 5V, RL = 8Ω	-	1.25	-	W
Total Harmonic Distortion	THD+N	VCC = 5V, RL = 8Ω, 1kHz	-	0.05	-	%
Signal-to-Noise Ratio	SNR	VCC = 5V, RL = 8Ω	-	85	-	dB
Input Sensitivity	VIN	VCC = 5V, RL = 8Ω, 1kHz	200	300	400	mV
Input Impedance	ZIN	-	-	10	-	kΩ
Shutdown Current	ISD	VCC = 5V	-	0.1	-	μA
Operating Temperature	TOPR	-	-40	-	85	°C
Storage Temperature	TSTG	-	-65	-	150	°C

Instructions for Using NJM2595M

1. Supply Voltage:

   • Ensure the supply voltage (VCC) is within the range of 4.5V to 5.5V. The typical operating voltage is 5V.

2. Quiescent Current:

   • The quiescent current (IQ) is typically 1.5mA at VCC = 5V. This is the current consumed by the device when no load is connected.

3. Output Current:

   • The maximum output current per channel (IOUT) can be up to 400mA, with a typical value of 300mA at VCC = 5V and a load resistance (RL) of 8Ω.

4. Output Power:

   • The typical output power per channel (POUT) is 1.25W at VCC = 5V and RL = 8Ω.

5. Total Harmonic Distortion (THD+N):

   • The total harmonic distortion plus noise (THD+N) is typically 0.05% at VCC = 5V, RL = 8Ω, and a frequency of 1kHz.

6. Signal-to-Noise Ratio (SNR):

   • The signal-to-noise ratio (SNR) is typically 85dB at VCC = 5V and RL = 8Ω.

7. Input Sensitivity:

   • The input sensitivity (VIN) is typically between 200mV and 400mV at VCC = 5V, RL = 8Ω, and a frequency of 1kHz.

8. Input Impedance:

   • The input impedance (ZIN) is typically 10kΩ.

9. Shutdown Current:

   • When the device is in shutdown mode, the shutdown current (ISD) is typically 0.1μA at VCC = 5V.

10. Operating Temperature:

    • The operating temperature (TOPR) range is from -40°C to 85°C.

11. Storage Temperature:

    • The storage temperature (TSTG) range is from -65°C to 150°C.

Additional Notes:

• Always ensure proper heat sinking if the device is expected to operate at high output currents or for extended periods.
• Use bypass capacitors (typically 10μF and 0.1μF) close to the VCC and GND pins to ensure stable operation.
• Connect the shutdown pin (SD) to VCC for normal operation or to GND to put the device into shutdown mode.

(For reference only)