Details

---

BUY MX29F040CQC-70G https://www.utsource.net/itm/p/12532829.html

Parameter	Symbol	Conditions	Min	Typ	Max	Unit
Supply Voltage	VCC	Operating	2.7	-	3.6	V
Standby Current	ICC(SB)	VCC = 3.0V, VPP = 0V	-	10	-	μA
Active Current	ICC(AC)	VCC = 3.0V, Reading	-	15	-	mA
Programming Current	ICC(PGM)	VCC = 3.0V, Writing	-	100	-	mA
Erase Time	tERASE	Block Erase	-	200	-	ms
Write Time	tWRITE	Page Program	-	2	-	ms
Read Access Time	tRAC	Typical	-	70	-	ns
Data Output Hold Time	tOH		0	-	20	ns
Address Setup Time	tAS		20	-	-	ns
Address Hold Time	tAH		0	-	20	ns
Data Setup Time	tDS		20	-	-	ns
Data Hold Time	tDH		0	-	20	ns
Chip Enable Setup Time	tCES		20	-	-	ns
Chip Enable Hold Time	tCEH		0	-	20	ns
Output Enable Setup Time	tOES		20	-	-	ns
Output Enable Hold Time	tOEH		0	-	20	ns
Write Enable Setup Time	tWES		20	-	-	ns
Write Enable Hold Time	tWEH		0	-	20	ns

Instructions for Use:

1. Power Supply:

   • Ensure the supply voltage (VCC) is within the specified range of 2.7V to 3.6V.
   • The programming voltage (VPP) should be set to 0V during normal operation.

2. Current Consumption:

   • Monitor the standby current (ICC(SB)) to ensure it does not exceed 10μA at 3.0V.
   • The active current (ICC(AC)) should be around 15mA during read operations.
   • The programming current (ICC(PGM)) can reach up to 100mA during write operations.

3. Timing Parameters:

   • Erase Time (tERASE): Block erase typically takes about 200ms.
   • Write Time (tWRITE): Page program operations take approximately 2ms.
   • Read Access Time (tRAC): The typical read access time is 70ns.
   • Data Output Hold Time (tOH): Ensure data output is held for at least 0ns but no more than 20ns.
   • Address Setup Time (tAS): Address setup time should be at least 20ns.
   • Address Hold Time (tAH): Address hold time should be between 0ns and 20ns.
   • Data Setup Time (tDS): Data setup time should be at least 20ns.
   • Data Hold Time (tDH): Data hold time should be between 0ns and 20ns.
   • Chip Enable Setup Time (tCES): Chip enable setup time should be at least 20ns.
   • Chip Enable Hold Time (tCEH): Chip enable hold time should be between 0ns and 20ns.
   • Output Enable Setup Time (tOES): Output enable setup time should be at least 20ns.
   • Output Enable Hold Time (tOEH): Output enable hold time should be between 0ns and 20ns.
   • Write Enable Setup Time (tWES): Write enable setup time should be at least 20ns.
   • Write Enable Hold Time (tWEH): Write enable hold time should be between 0ns and 20ns.

4. Operating Conditions:

   • Ensure all timing parameters are met to avoid data corruption or incorrect operation.
   • Refer to the device datasheet for detailed command sequences and specific application notes.

5. Handling and Storage:

   • Handle the device with care to prevent static damage.
   • Store in a dry, cool environment to maintain reliability.

(For reference only)