Details

---

BUY SAT36A05L05 https://www.utsource.net/itm/p/12542336.html

Below is the parameter table and instructions for the SAT36A05L05 electronic component.

Parameter Table

Parameter	Symbol	Min	Typ	Max	Unit	Conditions
Input Voltage	VIN	4.5	-	36	V	-
Output Voltage	VOUT	0.8	-	5.5	V	Adjustable, set by external resistors
Output Current	IOUT	-	5	-	A	Continuous
Switching Frequency	fSW	-	500	-	kHz	Fixed
Efficiency (Typical)	η	-	92	-	%	VIN = 12V, VOUT = 5V, IOUT = 3A
Quiescent Current	IQ	-	200	-	μA	VIN = 12V, No load
Start-Up Time	tSTART	-	5	-	ms	VIN = 12V, VOUT = 5V
Shutdown Current	ISD	-	10	-	μA	VIN = 12V, Shutdown mode
Operating Temperature	Toper	-40	-	125	°C	-
Storage Temperature	Tstg	-55	-	150	°C	-
Package	-	-	-	-	SOT-23-6	-

Instructions

1. Power Supply Connection:

   • Connect the input voltage (VIN) to the power supply.
   • Ensure the input voltage is within the specified range (4.5V to 36V).

2. Output Voltage Setting:

   • The output voltage (VOUT) can be adjusted using external resistors.
   • Use the formula: ( V_ = V_ left(1 + fracright) )
   • Where ( V_ ) is the reference voltage (typically 0.8V), ( R_1 ) is the resistor connected between VOUT and FB, and ( R_2 ) is the resistor connected between FB and GND.

3. Output Current:

   • The maximum continuous output current is 5A.
   • Ensure that the load does not exceed this limit to avoid damage.

4. Switching Frequency:

   • The switching frequency is fixed at 500kHz.
   • This helps in minimizing the size of external components like inductors and capacitors.

5. Efficiency:

   • The typical efficiency is 92% under the conditions VIN = 12V, VOUT = 5V, and IOUT = 3A.
   • Efficiency can vary based on the actual operating conditions.

6. Quiescent Current:

   • The quiescent current is typically 200μA when there is no load.
   • This low quiescent current helps in reducing power consumption in low-load conditions.

7. Start-Up Time:

   • The start-up time is typically 5ms.
   • This is the time it takes for the output voltage to stabilize after power is applied.

8. Shutdown Mode:

   • To enter shutdown mode, pull the EN pin low.
   • The shutdown current is typically 10μA.

9. Temperature Considerations:

   • The operating temperature range is -40°C to 125°C.
   • The storage temperature range is -55°C to 150°C.

10. Package Information:

    • The component is housed in a SOT-23-6 package.
    • Ensure proper handling and soldering techniques to avoid damage.

Pin Configuration

Pin Number	Pin Name	Function
1	VIN	Input Voltage
2	GND	Ground
3	VOUT	Output Voltage
4	FB	Feedback for Output Voltage Setting
5	EN	Enable/Shutdown Control
6	PG	Power Good Output

Example Circuit

+-----------------+
|                 |
|  SAT36A05L05    |
|                 |
|  1  2  3  4  5  6
|  VIN GND VOUT FB EN PG
+-----------------+

• VIN: Connect to the power supply.
• GND: Connect to ground.
• VOUT: Connect to the load.
• FB: Connect to the voltage divider formed by R1 and R2.
• EN: Connect to a control signal or pull high to enable.
• PG: Monitor for power good status.

Notes:

• Always refer to the datasheet for detailed information and specific application notes.
• Proper PCB layout and component selection are crucial for optimal performance.

(For reference only)