Details

---

BUY OPA627AU https://www.utsource.net/itm/p/12555263.html

Parameter	Symbol	Conditions	Min	Typ	Max	Unit
Supply Voltage	VCC	-	±5	±15	-	V
Quiescent Current	IQ	VCC = ±15V	-	4.5	-	mA
Input Offset Voltage	VIO	-	-	0.5	3	mV
Input Bias Current	IB	-	-	0.5	5	nA
Input Voltage Noise Density	en	f = 1kHz	-	1.1	-	nV/√Hz
Input Current Noise Density	in	f = 1kHz	-	0.1	-	pA/√Hz
Large Signal Voltage Gain	AV	VCC = ±15V, RL = 2kΩ	100	150	200	dB
Slew Rate	SR	-	2500	-	-	V/μs
Bandwidth (Small Signal)	BW	VCC = ±15V, G = +1, RL = 2kΩ	-	180	-	MHz
Output Voltage Swing	VOS	VCC = ±15V, IL = ±10mA	-13	-	13	V
Common Mode Rejection Ratio	CMRR	VCC = ±15V, G = +1	90	-	-	dB
Power Supply Rejection Ratio	PSRR	VCC = ±15V, G = +1	90	-	-	dB
Output Impedance	Zout	f = 1MHz	-	15	-	Ω

Instructions for Use:

1. Supply Voltage: The OPA627AU operates with a supply voltage range of ±5V to ±15V. Ensure the power supply is stable and within this range to avoid damage or performance degradation.

2. Quiescent Current: The typical quiescent current is 4.5mA at ±15V supply. This should be considered in power budget calculations.

3. Input Offset Voltage: The input offset voltage can range from 0.5mV to 3mV. Use trimming circuits if precise offset adjustment is required.

4. Input Bias Current: The input bias current is typically 0.5nA to 5nA. Use high-impedance sources to minimize errors due to bias currents.

5. Noise Performance: The OPA627AU has low noise characteristics, with voltage noise density of 1.1nV/√Hz and current noise density of 0.1pA/√Hz at 1kHz. This makes it suitable for high-fidelity audio and precision measurement applications.

6. Gain and Bandwidth: The large signal voltage gain is between 100dB and 200dB, and the small signal bandwidth is 180MHz. These parameters make the OPA627AU suitable for high-speed applications.

7. Slew Rate: The slew rate is 2500V/μs, which is important for maintaining signal integrity in fast-switching applications.

8. Output Voltage Swing: The output voltage swing is ±13V with a load current of ±10mA, ensuring a wide dynamic range.

9. Common Mode Rejection Ratio (CMRR): The CMRR is 90dB, indicating good rejection of common-mode signals.

10. Power Supply Rejection Ratio (PSRR): The PSRR is also 90dB, ensuring that variations in the power supply have minimal impact on the output.

11. Output Impedance: The output impedance is 15Ω at 1MHz, which should be considered when designing the load circuit.

12. Layout Considerations: Use proper PCB layout techniques to minimize parasitic capacitances and inductances, especially for high-frequency applications. Keep input leads short and use bypass capacitors close to the power pins.

13. Thermal Management: Ensure adequate heat dissipation, especially in high-power applications, to maintain reliable operation and prevent overheating.

14. Storage and Handling: Store the OPA627AU in a dry environment and handle with care to avoid electrostatic discharge (ESD) damage. Use appropriate ESD protection measures during handling and assembly.

(For reference only)