Details

---

BUY AD8063ARZ https://www.utsource.net/itm/p/12604221.html

Parameter	Symbol	Conditions	Min	Typ	Max	Unit
Supply Voltage	VCC	Operating	2.7	-	5.5	V
Quiescent Current	IQ	Per Amplifier, VCC = 5V	-	1.8	-	mA
Input Voltage Range	VI	VCC = 5V	0	-	3.5	V
Output Voltage Swing	VOUT	VCC = 5V, RL = 1kΩ	0.02	-	4.9	V
Bandwidth	fBW	VCC = 5V, G = +1	-	130	-	MHz
Slew Rate	SR	VCC = 5V	-	300	-	V/μs
Large Signal Voltage Gain	AV	VCC = 5V, f = 1kHz	100	-	-	dB
Input Bias Current	IB	VCC = 5V	-	0.1	-	nA
Input Offset Voltage	VOS	VCC = 5V	-	1.5	-	mV
Common-Mode Rejection Ratio	CMRR	VCC = 5V, f = 1kHz	-	80	-	dB
Power Supply Rejection Ratio	PSRR	VCC = 5V, f = 1kHz	-	80	-	dB
Noise Voltage Density	en	VCC = 5V, f = 1kHz	-	5	-	nV/√Hz

Instructions for Use:

1. Supply Voltage:

   • Ensure the supply voltage (V_CC) is within the range of 2.7V to 5.5V.
   • Connect the supply voltage to the V_CC pin and ground to the GND pin.

2. Input Voltage:

   • The input voltage should not exceed the range from 0V to 3.5V when V_CC is 5V.
   • Connect the input signal to the non-inverting (IN+) or inverting (IN-) input pins.

3. Output Voltage:

   • The output voltage swing can range from 0.02V to 4.9V with a 1kΩ load when V_CC is 5V.
   • Connect the output to the desired load or next stage of the circuit.

4. Bandwidth and Slew Rate:

   • The amplifier has a bandwidth of 130MHz at a gain of +1.
   • The slew rate is 300V/μs, which is suitable for high-speed applications.

5. Gain Configuration:

   • Set the gain using external resistors connected between the output and the inverting input.
   • For unity gain, connect a direct wire or a low-value resistor between the output and inverting input.

6. Bias and Offset:

   • The input bias current is very low (0.1nA), reducing the need for large input resistors.
   • The input offset voltage is 1.5mV, which may need to be compensated for in precision applications.

7. Noise Considerations:

   • The noise voltage density is 5nV/√Hz, making it suitable for low-noise applications.

8. Power Supply Rejection:

   • The power supply rejection ratio (PSRR) is 80dB, ensuring good stability against power supply variations.

9. Common-Mode Rejection:

   • The common-mode rejection ratio (CMRR) is 80dB, providing good performance in rejecting common-mode signals.

10. Thermal Management:

    • Ensure adequate heat dissipation if operating at high power levels or in high ambient temperatures.

11. Layout Considerations:

    • Use short, wide traces for power and ground connections to minimize inductance and resistance.
    • Place bypass capacitors (0.1μF) close to the power pins to filter out high-frequency noise.

12. Storage and Handling:

    • Store the device in a dry environment to prevent moisture damage.
    • Handle with care to avoid static discharge, which can damage the sensitive components.

For detailed application notes and further information, refer to the AD8063ARZ datasheet provided by Analog Devices.

(For reference only)