Details

---

BUY OP97F https://www.utsource.net/itm/p/12611803.html

Parameter	Symbol	Min	Typical	Max	Unit	Conditions
Supply Voltage	VCC	2.7	-	6.0	V
Quiescent Current	IQ	-	13	15	渭A	VCC = 5V, TA = 25掳C
Input Offset Voltage	VIO	-5	0	5	渭V	VCC = 5V, TA = 25掳C
Input Bias Current	IB	-	2	4	nA	VCC = 5V, TA = 25掳C
Input Voltage Range	VIN	0	-	VCC - 1.5	V
Output Voltage Swing	VOUT	0	-	VCC - 1.5	V	RL = 10k惟
Slew Rate	SR	-	0.3	-	V/渭s
Bandwidth	BW	-	1.2	-	MHz	VCC = 5V, G = +1, RL = 2k惟
Common-Mode Rejection Ratio	CMRR	100	-	120	dB	VCC = 5V, f = 0.1Hz to 10kHz
Power Supply Rejection Ratio	PSRR	100	-	120	dB	VCC = 5V, f = 0.1Hz to 10kHz
Operating Temperature	TA	-40	-	85	掳C

Instructions for Use:

1. Supply Voltage:

   • The OP97F can operate with a supply voltage ranging from 2.7V to 6.0V. Ensure the supply voltage is within this range to avoid damage to the device.

2. Quiescent Current:

   • The quiescent current is typically 13渭A at 5V supply and 25掳C ambient temperature. This value may vary slightly with different operating conditions.

3. Input Offset Voltage:

   • The input offset voltage is typically 0渭V at 5V supply and 25掳C ambient temperature, with a maximum of 卤5渭V. This parameter is crucial for precision applications.

4. Input Bias Current:

   • The input bias current is typically 2nA at 5V supply and 25掳C ambient temperature, with a maximum of 4nA. This affects the stability and accuracy of the op-amp in high-impedance circuits.

5. Input Voltage Range:

   • The input voltage range should be between 0V and V_CC - 1.5V. Exceeding these limits can cause the op-amp to malfunction or be damaged.

6. Output Voltage Swing:

   • The output voltage swing is from 0V to V_CC - 1.5V when the load resistance is 10k惟. Ensure the load resistance is appropriate to achieve the desired output swing.

7. Slew Rate:

   • The typical slew rate is 0.3V/渭s. This parameter is important for high-frequency applications to ensure that the op-amp can follow rapid changes in the input signal.

8. Bandwidth:

   • The typical bandwidth is 1.2MHz at a gain of +1 and a load resistance of 2k惟. This parameter determines the frequency range over which the op-amp can operate effectively.

9. Common-Mode Rejection Ratio (CMRR):

   • The CMRR is typically 100dB to 120dB at frequencies from 0.1Hz to 10kHz. A higher CMRR indicates better rejection of common-mode signals, which is important for differential amplification.

10. Power Supply Rejection Ratio (PSRR):

    • The PSRR is typically 100dB to 120dB at frequencies from 0.1Hz to 10kHz. A higher PSRR indicates better rejection of power supply noise, which is crucial for maintaining signal integrity.

11. Operating Temperature:

    • The OP97F is designed to operate over a temperature range from -40掳C to 85掳C. Ensure the ambient temperature is within this range to maintain optimal performance.

Additional Notes:

• Always use bypass capacitors (typically 0.1渭F and 10渭F) between the supply pins and ground to filter out any noise and ensure stable operation.
• For best performance, keep the PCB layout clean and minimize the length of input and output traces to reduce parasitic capacitance and inductance.
• When using the OP97F in high-precision applications, consider the effects of temperature on the parameters and use appropriate compensation techniques if necessary.

(For reference only)